Aftermarket parts

[okiehusky]

Have been looking for a Talon/Vortex/Renthal 51t sprocket for my '12 TXC310 for over a week! Have checked 7602 Racing, Motosportz, & Tourtech. Pretty slim pickins'. Other than European vendors, is there a good source here in the good old US of A for Husky aftermarket goodies? I had to get graphics from Germany. Now that is an experience..........Anyhoo, any leads on this caper would be most welcome.

 

[Coffee]

Do not know of the actual vendors, but I buy sprockets from my dealer, MotoXotica.

Maybe check here?
http://www.cafehusky.com/pages/chsponsors/

 

[MOTORHEAD]

Yes, Dan had them the last time I was looking for a Rental.

 

[okiehusky]

Thanks Coffee!!! Always enjoy perusing new web sites. So I'll take a stroll through the goodies, cast a net, and see what ends up in the basket!

 

[rancher1]

Hi okiehusky, I see your location is sand springs, I think I went riding around there once. I there riding in your area?

 

[okiehusky]

Rancher1---you betcha. Several locations with varying terrain, soils and plenty of blackjacks. Speaking of trees, having a hell of a time mounting barkbusters to the TXC. Can't clear the front brake like coming out of the reservoir. Am I not smart enough to figure it out or is this a common malady? What say you folks?

 

[Irocleis]

i just mounted E/E bark busters w/ roost deflectors on my txc... the e/e brackets are nice because they dip down and allow room for the clutch and brake cable

 

[Irocleis]

E/E- enduro engineering. But i was also browsing this thread because I was in search of some aftermarket parts as well. If anyone knows of any good places for graphics please share!

 

[Mike-AK]

Rancher1---you betcha. Several locations with varying terrain, soils and plenty of blackjacks. Speaking of trees, having a hell of a time mounting barkbusters to the TXC. Can't clear the front brake like coming out of the reservoir. Am I not smart enough to figure it out or is this a common malady? What say you folks?

I could not get any of the bar mounted options to fit on my TE310 either. Like you say, could not get them to clear the brake banjo and line. I ended up going with the Highway Dirt Bikes bark busters. Excellent product. Only downside is I had to upgrade both the upper and lower bar clamps in order to install the HDB guards. The upside is the slightly higher bar height is really comfortable.

 

[Mike-AK]

i just mounted E/E bark busters w/ roost deflectors on my txc... the e/e brackets are nice because they dip down and allow room for the clutch and brake cable

I tried the EE guards but they would not clear the brake line without being in a funky position. Also I was concerned about the guards taking a whack and rotating on the bars, taking out the brake or clutch line with them.

 

[okiehusky]

Well poop. Was on the verge of buying the EE's. I put the previously purchased busters on my KDX. Hate to cough up the dough and then end up with the same problem. Well, they could go on my KX. Which does me absolutely no good when my pinkies are wrapped around Husky bars. Still may spring for the EE's. The saga continues....................

 

[Motosportz]

would these types of mounts clear it on your bike?

I personally like the triple clamp mounts as it eliminates the inner bar mount altogether

Many people use them on the single top mount bolt design just fine.

 

[Johnrg]

I think the Center Mount clamps look like a good option... http://store.cycraracing.com/ceremo7ba.html
Seen a setup on the forum and should clear everything leaving room for tie downs/hooks. A good savings over he HDB keeping all else as stock.

 

[okiehusky]

I'll have to study a bit on the CYCRAs. They look a lot like the EE's. Well sorta. Kinda. Center clamp may be the ticket. Onward we go.

 

[Mike-AK]

I'll have to study a bit on the CYCRAs. They look a lot like the EE's. Well sorta. Kinda. Center clamp may be the ticket. Onward we go.

I think the Cycra's with the center reach mount would be fine, as are the Highway Dirt Bikes guards. There is just too much going on in the short space in between the grips and the bar clamps to make mounting anything else practical in my opinion.

 

[Irocleis]

Heres a couple pics i took with the e/e bark busters on my txc250


Uploaded with ImageShack.us


Uploaded with ImageShack.us

 

[okiehusky]

Motosportz------I sprang for the u-mounts. Appears to be the most logical solution. Thanks for the head's up on those little diddies! How are you guys looking on a 51t aluminum sprocket? In a tasteful anodized red. Didn't see one on the website. Apparently those puppies are few and far between.

 

[Motosportz]

Motosportz------I sprang for the u-mounts. Appears to be the most logical solution. Thanks for the head's up on those little diddies! How are you guys looking on a 51t aluminum sprocket? In a tasteful anodized red. Didn't see one on the website. Apparently those puppies are few and far between.

Hope it works out for you.

- Contact Motosportzmike on this site for the sprocket.

 

[Motosportz]

Heres a couple pics i took with the e/e bark busters on my txc250

Looks good. Looks like you could also spin the L shaped hose 180 for even more clearance if you wanted to move your levers down.

 

[troy deck]

Have been looking for a Talon/Vortex/Renthal 51t sprocket for my '12 TXC310 for over a week! Have checked 7602 Racing, Motosportz, & Tourtech. Pretty slim pickins'. Other than European vendors, is there a good source here in the good old US of A for Husky aftermarket goodies? I had to get graphics from Germany. Now that is an experience..........Anyhoo, any leads on this caper would be most welcome.

supersprox had'em for my 12 cr 125