1. 2 Stroke Husqvarna Motorcycles Made In Italy - About 1989 to 2014
    WR = 2st Enduro & CR = 2st Cross

250-500cc Marzocchi Broken 45mm Shiver Rebound Adjuster Screw :(

Discussion in '2 Stroke' started by mr_manny, Nov 20, 2021.

  1. mr_manny Husqvarna
    B Class

    Location:
    Jalisco, Mexico
    Husqvarna Motorcycle:
    wr250
    Noticed a thrashed rebound screw on my shiver fork.
    Anyone ever replace one of these?

    brokenADJ.jpg
  2. Dirtdame Administrator

    Location:
    Escondido, California
    Husqvarna Motorcycle:
    07 TE450,11 WR300,13 WR125,18 FE501
    Other Motorcycles:
    KDX200,Beta XT,MV Agusta Brutale
    Not listed as a rebuildable part. Fork cap not manufactured anymore. You might find a cap assembly on Ebay eventually.
  3. Picklito Husqvarna
    Pro Class

    Location:
    Washington
    Husqvarna Motorcycle:
    430, 430, 430, ,400, 175
    Other Motorcycles:
    KTM250xc, KTM500mx, KTM440exc
    As above. Anything Marzocchi is nearly unobtanium anymore. I've purchased whole forks just to get parts.
  4. mr_manny Husqvarna
    B Class

    Location:
    Jalisco, Mexico
    Husqvarna Motorcycle:
    wr250
    May have to live with it.
    Thanks for the replies.
  5. mr_manny Husqvarna
    B Class

    Location:
    Jalisco, Mexico
    Husqvarna Motorcycle:
    wr250
    I did receive a few links to a couple of European sites that carry it...it's close to $100US.
    Will continue going through my wr250 first...see what else needs attention.
  6. husky jim Husqvarna
    Pro Class

    Location:
    USA
    Husqvarna Motorcycle:
    14 WR300, 87 430wr, 86 430ae, Tr650
    Just buy a New set.

    https://www.ebay.com/itm/334095153889

    I offer him $199+ ship, that's what I paid for a set
    Should bolt right up, here they are my 430ae using a set of '93 triples, modern hub, axle
    Then you will have extra parts from your old set, if needed down the road

    auto hub2.jpg autofront3.jpg
  7. mr_manny Husqvarna
    B Class

    Location:
    Jalisco, Mexico
    Husqvarna Motorcycle:
    wr250
    Very Tempting.

    I'm just getting back into riding...reason for picking up a project wr250.

    If I love it:
    Sell it, and pickup something newer.
    or
    Keep it, and address remaining issues.

    Will cross that bridge when I get there :)
  8. husky jim Husqvarna
    Pro Class

    Location:
    USA
    Husqvarna Motorcycle:
    14 WR300, 87 430wr, 86 430ae, Tr650
  9. mr_manny Husqvarna
    B Class

    Location:
    Jalisco, Mexico
    Husqvarna Motorcycle:
    wr250
    Thanks husky jim.
    I actually scored a cap from flyingbob here on cafehusky.

    Appreciate the community we have here.
    Cheers :cheers:
  10. mr_manny Husqvarna
    B Class

    Location:
    Jalisco, Mexico
    Husqvarna Motorcycle:
    wr250
    Replacement Cap arrived :)
    Thanks again flyingbob :cool:

    newCAP.jpg
    flyingbob, Picklito and Dirtdame like this.
  11. Theo Husqvarna
    AA Class

    Location:
    Lombardy, Italy
    Husqvarna Motorcycle:
    SM 610 I.E.
    Other Motorcycles:
    2001 YZ250
    I wish I noticed this thread when it was opened.
    Anyhow, I did replace those screws in my Shiver fork years ago.
    I found them in a suspensions shop; I don't know whether they could be still found nowadays.
    The screw is sealed by an oring:

    assembled.jpg

    screw and oring.jpg

    And from the side there is a ball which holds it in position. The ball has some preload from a spring, compressed by a set screw. When we adjust the rebound we hear clicks because as the yellow (brass?) screw is rotated, the ball retracts and then enters the next groove: in that moment it clicks.

    screw, spring, ball.jpg

    hole.jpg
    flyingbob and Dirtdame like this.
  12. mr_manny Husqvarna
    B Class

    Location:
    Jalisco, Mexico
    Husqvarna Motorcycle:
    wr250
    Good Info Theo

    Thanks for sharing...cheers :cheers:
    flyingbob likes this.