• Hi everyone,

    As you all know, Coffee (Dean) passed away a couple of years ago. I am Dean's ex-wife's husband and happen to have spent my career in tech. Over the years, I occasionally helped Dean with various tech issues.

    When he passed, I worked with his kids to gather the necessary credentials to keep this site running. Since then (and for however long they worked with Coffee), Woodschick and Dirtdame have been maintaining the site and covering the costs. Without their hard work and financial support, CafeHusky would have been lost.

    Over the past couple of weeks, I’ve been working to migrate the site to a free cloud compute instance so that Woodschick and Dirtdame no longer have to fund it. At the same time, I’ve updated the site to a current version of XenForo (the discussion software it runs on). The previous version was outdated and no longer supported.

    Unfortunately, the new software version doesn’t support importing the old site’s styles, so for now, you’ll see the XenForo default style. This may change over time.

    Coffee didn’t document the work he did on the site, so I’ve been digging through the old setup to understand how everything was running. There may still be things I’ve missed. One known issue is that email functionality is not yet working on the new site, but I hope to resolve this over time.

    Thanks for your patience and support!

What the EFI/Carb forum is for

Coffee

Coffee

CH Owner
Staff member
This forum is to put EFI & Carb information for the Husqvarna bikes.

The threads that are focused on Husqvarna EFI should be in this forum regardless of which Husqvarna bike.

  1. The non-Husqvarna bike EFI threads such as "does anyone have the ability to adjust the EFI settings on Husaberg?" should go in the General (Main) forum.
  2. The non-technical or miscellaneous Husqvarna EFI threads such as "should I buy this 2007 TE450? Does it have EFI?" should go in the Main forum.
  3. The carb discussions can go in the bike specific areas or in this area. Ideally there will be at least a few basic reference posts on carb jetting in this forum.
The goal is to collect in one place the EFI focused threads that may be of interest in the future. Having the initials "EFI" does not automatically mean it should be in this section, use your best judgment.

Please post any questions or suggestions.

:cheers:

EDIT: Updated July 19th 2012
.
 
hello
I have a te 450 08 and in low rpm it goes "baf" an shuts down also it is spinning in wet and mud ant the torque is not so good
So I dont have an i beat or a dealer near my house to get the bike
I also want to have the map switch
can u help me?
 
Map switch isn't available for our 08's unfortunately. Take a video of what it's doing and upload it.
 
2008-2012 Mikuni
2013-2014 Italian bikes - Keihin

I 'think' the new KTM/Husaberg derived Huskies are also Keihin.
 
Ok so iv got to the point of bein sick of husqvarnas choice to give the sms630 a terible fuel map iv got pc5 which made a noticeable difrence but still not brilliant im in 2 minds ditch the efi all together and use a keihin fcr41 or arrow ecu combo with autotune and yes efi is superior i no that but in nz $ im looking at 2g ish for cans and ecu and a minimum of 700 for dyno so lets say 3g now carb conversion anyones guess at this point but lets say round a g
In my mind yes carbs are more work but i can set them up in my sleep efi set once and forget bout it or do i bite the bullet and sell and become a husky hater
Opinions please im at my wits end with this bike i love it but it shouldt cost the amount of a ktm525 to get it goin to its full potential
 
I have a 2008 TE 510, Had the same issues. I finally got the kit from Bills in Oregon. You disconnect the O2 sensor n cap it, plug in the jumper under the tank where the O2 was plugged in. Bought and hooked up the new fuel injection fix. not Power Commander, the other one...not to say PC could also work.
Anyway. That took care of everything. Runs very well now.
 
Iv got o2 pluged resistor installed
Got shot of air box installed uni filter
Fmf slip on
42t rear sproket
Pcv with ziptys 630race map
Goes good want to power wheelie pullin off from first does it till 3rd but other than that got to clutch it
Is the arrow upgraid with ecu worth the money
 
Yah it goes good dont get me wrong always smiling when on my 630 but i no its got more the iv had a think im guna save up for the arrow ecu combo all i realy want is to power wheelie a little easier in 2nd 3rd like you see any other motard do with ease
 
Me and a buddy just got Ibeat loaded on a old laptop.Haven't tried it on a our bikes yet,but it is over fulling the screen.Is it my computer or the software? Can't seem to find a way fit the Ibeat into the screen.
 
auto said:
Me and a buddy just got Ibeat loaded on a old laptop.Haven't tried it on a our bikes yet,but it is over fulling the screen.Is it my computer or the software? Can't seem to find a way fit the Ibeat into the screen.
Click to expand...
No idea on this, it comes up in a window on mine.
 
auto said:
Me and a buddy just got Ibeat loaded on a old laptop.Haven't tried it on a our bikes yet,but it is over fulling the screen.Is it my computer or the software? Can't seem to find a way fit the Ibeat into the screen.
Click to expand...

Try pushing the Windows key and the Up arrow at the same time.
 
You must log in or register to reply here.
Back
Top