1. 2 Stroke Husqvarna Motorcycles Made In Italy - About 1989 to 2014
    WR = 2st Enduro & CR = 2st Cross

250-500cc Wr360 kickstarter leak

Discussion in '2 Stroke' started by ajaxhawk, Apr 13, 2018.

  1. ajaxhawk Husqvarna
    B Class

    Location:
    Qld Australia
    Husqvarna Motorcycle:
    te250
    Hi guys , i had purchased the bike with a fresh rebuild been done by previous owner , a very tidy bike with the usual quirks that seem quite common . Its had a crack around the kickstarter fixed with some kind of epoxy resin which seems to be holding up fine with kickstarting regularly . But it leaks tranny fluid from kickstarter shaft , had a look at the parts fiche and doesnt even seem to have a seal present ??? Any suggestions on how to stop the leak on an otherwise awesome bike
  2. ajaxhawk Husqvarna
    B Class

    Location:
    Qld Australia
    Husqvarna Motorcycle:
    te250
  3. 2premo Husqvarna
    Pro Class

    Location:
    Northern NV
    Husqvarna Motorcycle:
    98 WR360, 1987 WR430, 1988 XC430
    Other Motorcycles:
    Sherco 300, 2002 KTM 380EXC
    what's confusing is the bearing and seal are shown with the center cases, very confusing
    8000 48209 is the part referenced as #21

    on a different note, your avatar, thought they banned guns down unda
  4. ajaxhawk Husqvarna
    B Class

    Location:
    Qld Australia
    Husqvarna Motorcycle:
    te250
    So there is a seal ????? Wtf!!
    No you can still own guns , just lots of red tape to start with.
  5. ajaxhawk Husqvarna
    B Class

    Location:
    Qld Australia
    Husqvarna Motorcycle:
    te250
    Oh and 2premo . Thanks
  6. ajaxhawk Husqvarna
    B Class

    Location:
    Qld Australia
    Husqvarna Motorcycle:
    te250
    Whats part #18 , is that internal??
  7. 2premo Husqvarna
    Pro Class

    Location:
    Northern NV
    Husqvarna Motorcycle:
    98 WR360, 1987 WR430, 1988 XC430
    Other Motorcycles:
    Sherco 300, 2002 KTM 380EXC

    pretty sure its the output shaft seal behind the sprocket
    ajaxhawk likes this.
  8. ajaxhawk Husqvarna
    B Class

    Location:
    Qld Australia
    Husqvarna Motorcycle:
    te250
  9. ajaxhawk Husqvarna
    B Class

    Location:
    Qld Australia
    Husqvarna Motorcycle:
    te250
    So i dug all the resin shit off , it looks like hes put a sleeve in to protect the casing at the expense of an oil leak .can anyone confirm if this is normal or otherwise please. Im assuming this is where the oil seal normally goes
  10. rancher1 Husqvarna
    Pro Class

    Location:
    WA
    The sleeve is where the oil seal goes. the oil seal is # 21. You could just think of it as a self oiler for the chain and change oil on a regular basis.
    Petar likes this.
  11. ajaxhawk Husqvarna
    B Class

    Location:
    Qld Australia
    Husqvarna Motorcycle:
    te250
    Thanks rancher 1
  12. Ran Caulfield Husqvarna
    AA Class

    Location:
    Qld Australia
    Husqvarna Motorcycle:
    12 Wr300,13 WR125
    Other Motorcycles:
    none at the mo
    Could you perhaps try an O ring on the shaft to stem the flow.
  13. ajaxhawk Husqvarna
    B Class

    Location:
    Qld Australia
    Husqvarna Motorcycle:
    te250
    Thats exactly what i did ☺☺, i ve ordered a couple seals from the states , but until they get here ive put a thick oring behind a nylon washer and wedged the kicker against it . Went for a 30km enduro ride last weekend and worked a treat