1. Husqvarna Motorcycles Made In Sweden - About 1988 and older

Oil viscosity

Discussion in 'Vintage/Left Kickers' started by Caden, Aug 15, 2016.

  1. Caden Husqvarna
    C Class

    Husqvarna Motorcycle:
    1983 husquavarna 125xc
    Other Motorcycles:
    1983 Honda cx650c
    My 83 cr plates are dragging a lot. I use klotz 30w chain and transmission oil. And I my plates won't disengage. Help please!!!
    Caden, Aug 15, 2016
    #1

  2. ruwfo Administrator

    Location:
    NJ
    Husqvarna Motorcycle:
    1980 390CR, 1982 430CR, 1984 400WR
    Other Motorcycles:
    1985 250XC, 2016 FJ-09
    Jump start the bike & then get it into 3rd gear, gas it, then pull in the clutch lever, should unstick them.. My 87 250 does it all the time , cause I only ride it couple of times a year.. Works ever time on my bike...

    Husky John
    ruwfo, Aug 16, 2016
    #2

  3. justintendo klotz super techniplate junkie

    Location:
    mercer, pa/northwest pa
    Husqvarna Motorcycle:
    84 250,86 400,87 430,88 250,95 360
    Other Motorcycles:
    99 kawasaki zrx 1100
    have you adjusted the clutch yet? in the middle of the basket?
    if everything is adjusted, the problem is those damn aluminum plates. you will have to start the bike, run along side it, pop into first and get on. after that ride around with the clutch pulled in and goose the throttle some, eventually it will pop.
    justintendo, Aug 16, 2016
    #3

  4. Kartwheel68 Husqvarna
    Pro Class

    Location:
    Newnan, Georgia
    Husqvarna Motorcycle:
    82 125XC, 250XC, 430XC, 430WR, 250CR
    Other Motorcycles:
    83 175WR , 76 250WR, 74 250 Mag
    Use ATF type F.
    Kartwheel68, Aug 16, 2016
    #4

  5. Caden Husqvarna
    C Class

    Husqvarna Motorcycle:
    1983 husquavarna 125xc
    Other Motorcycles:
    1983 Honda cx650c
    Well when I took the plates out. They were stuck together. I put them in oil. And I'm gonna put them back in after a little while. And see if my problems at fixed. Because the clutch plates are in good condition.
    Caden, Aug 17, 2016
    #5

  6. markt2 Husqvarna
    AA Class

    Location:
    Nevada
    Husqvarna Motorcycle:
    1976 250CR (times 2)
    Other Motorcycles:
    Several vintage Yamahas
    markt2, Aug 19, 2016
    #6

  7. Bigbill Husqvarna
    Pro Class

    Husqvarna Motorcycle:
    '83 250wr
    Other Motorcycles:
    0 right now
    I put the plates on a flat surface to make sure there flat not warped.
    Bigbill, Aug 20, 2016
    #7

  8. Caden Husqvarna
    C Class

    Husqvarna Motorcycle:
    1983 husquavarna 125xc
    Other Motorcycles:
    1983 Honda cx650c
    I did. They aren't warped. It's because the bike sat for a while. I got the clutch back together and it now works. Onward to find a gasket. Because making my own failed. And I won't but a bad gasket in that bike. Thanks guys
    Caden, Aug 22, 2016
    #8